收藏本站
NOIL1SM0300A
The data at the output of the sensor is clocked on the rising
edge of CLK. There is a delay of 3.2 ns between the rising
edge of CLK and a change in DATA<9:0>. After this delay
DATA<9:0> needs 6 ns to become stable within 10% of
VDDD. This means that DATA<9:0> is stable for a time
CLK
equal to the clock period minus 6 ns. Figure 22 illustrates
this.
NOTE: In slave mode, line valids that occur beyond the
desired image window should be discarded by
the user ’s image data acquisition system
DATA <9:0>
INVALID
VALID
INVALID
VALID
? INVALID
LINE_VALID
4ns
3.2ns
3.2 + 6ns
6ns
Clk period - 6ns
Figure 22. DATA<9.0> Valid Timing
Readout Timing in Slave Mode
The start pointer of the window to readout is determined
by the START_X and START_Y registers (as by readout in
master mode). The size of the window in x-direction is also
determined by the NB_OF_PIX register. The length of the
window in y-direction is determined by the externally
applied integration timing. The sensor does not know the
desired y-size to readout. It therefore reads out all lines
starting from START_Y. The readout of lines continues until
the user decides to start the FOT.
Even when the line pointer wants to address non existing
rows (row 481 and higher), the sequencer continues to run
in normal readout mode. This means that FRAME_VALID
remains high and LINE_VALID is toggled as if normal lines
are readout.
The controller should take care of this and ignore the
LINE_VALIDs that correspond with non existing lines and
LINE_VALIDs that correspond with lines that are not inside
the desired readout window.
The length of the FOT and ROT is still controlled by the
GRAN register as described in this data sheet.
Readout time longer than integration time
The sensor should be timed according to the formulas and
diagram here:
1. INT_TIME_1 should be brought high at time
(read_t - int_t) and preferably immediately after
the falling edge of LINE_VALID.
2. At time read_t all INT_TIME_x should
simultaneous go low to start the FOT. This is
immediately after the falling edge of the last
LINE_VALID of the desired readout window.
INT_TIME1
FOT
Reset
Readout
Integration
FOT
Readout time shorter than integration time
The sensor should be timed according to the formulas and
diagram here:
1. INT_TIME_1 should be brought high after a
minimum 2 m s reset time and preferably
immediately after the falling edge of the first
LINE_VALID.
2. At time read_t after the last valid LINE_VALID of
the desired window size, all other LINE_VALIDs
should be ignored.
3. After the desired integration length all
INT_TIME_x should simultaneous go low to start
the FOT.
INT_TIME1
FOT
Readout
Reset
Dummy
LINE_VALIDs
Integration
FOT
http://onsemi.com
21
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
NOIL2SC1300A-GDC IC IMAGE SENSOR LUPA1300 168PGA
NOIV1SE025KA-GDC IC IMAGE SENSOR 25MP 355PGA
NP100P04PDG-E1-AY MOSFET P-CH -40V MP-25ZP/TO-263
NP100P04PLG-E1-AY MOSFET P-CH -40V MP-25ZP/TO-263
NP100P06PDG-E1-AY MOSFET P-CH -60V MP-25ZP/TO-263
NP100P06PLG-E1-AY MOSFET P-CH -60V MP-25ZP/TO-263
NP109N04PUJ-E1B-AY MOSFET N-CH 40V MP-25ZP/TO-263
NP109N055PUJ-E1B-AY MOSFET N-CH 55V MP-25ZP/TO-263
相关代理商/技术参数
NOIL1SM1300AWES 制造商:ON Semiconductor 功能描述:PW/H
NOIL1SM4000A 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:LUPA4000: 4 MegaPixel High Speed CMOS Sensor
NOIL1SM4000A-GDC 功能描述:IC IMAGE SENSOR LUPA4000 127PGA RoHS:是 类别:传感器，转换器 >> 图像，相机 系列:* 标准包装:480 系列:- 象素大小:6.7µm x 6.7µm 有源象素阵列:768H x 488V 每秒帧数:52 电源电压:3.3V 类型:CMOS 成像 封装/外壳:48-QFP 供应商设备封装:48-QFP 包装:托盘 请注意:* 配用:4H2105-ND - HEADBOARD FOR KAC-004014H2104-ND - KIT EVAL FOR KAC-00401 其它名称:4H20954H2095-NDKAC-00401-CBC-LB-A0
NOIL1SN3000A-GDC 功能描述:IC IMAGE SENSOR LUPA3000 369PGA RoHS:是 类别:传感器，转换器 >> 图像，相机 系列:* 标准包装:480 系列:- 象素大小:6.7µm x 6.7µm 有源象素阵列:768H x 488V 每秒帧数:52 电源电压:3.3V 类型:CMOS 成像 封装/外壳:48-QFP 供应商设备封装:48-QFP 包装:托盘 请注意:* 配用:4H2105-ND - HEADBOARD FOR KAC-004014H2104-ND - KIT EVAL FOR KAC-00401 其它名称:4H20954H2095-NDKAC-00401-CBC-LB-A0
NOIL2SC1300A-GDC 功能描述:图像传感器和彩色传感器 LUPA1300-2 COLOR PGA168 RoHS:否 制造商:Avago Technologies 类型:Color Sensors 工作电源电压:2.5 V 封装 / 箱体: 图象大小: 颜色读出:Color 最大工作温度:+ 70 C 最小工作温度:- 25 C 封装:Reel
NOIL2SM1300A-GDC 功能描述:IC IMAGE SENSOR LUPA1300 168PGA RoHS:是 类别:传感器，转换器 >> 图像，相机 系列:* 标准包装:480 系列:- 象素大小:6.7µm x 6.7µm 有源象素阵列:768H x 488V 每秒帧数:52 电源电压:3.3V 类型:CMOS 成像 封装/外壳:48-QFP 供应商设备封装:48-QFP 包装:托盘 请注意:* 配用:4H2105-ND - HEADBOARD FOR KAC-004014H2104-ND - KIT EVAL FOR KAC-00401 其它名称:4H20954H2095-NDKAC-00401-CBC-LB-A0
NOIL2SM1300A-GWC 功能描述:IC IMAGE SENSOR LUPA1300 168PGA RoHS:是 类别:传感器，转换器 >> 图像，相机 系列:* 标准包装:480 系列:- 象素大小:6.7µm x 6.7µm 有源象素阵列:768H x 488V 每秒帧数:52 电源电压:3.3V 类型:CMOS 成像 封装/外壳:48-QFP 供应商设备封装:48-QFP 包装:托盘 请注意:* 配用:4H2105-ND - HEADBOARD FOR KAC-004014H2104-ND - KIT EVAL FOR KAC-00401 其它名称:4H20954H2095-NDKAC-00401-CBC-LB-A0
NOIS1SC1000A-HHC 制造商:ON Semiconductor 功能描述:STAR1000 COLOR JLCC84 - Trays 制造商:ON Semiconductor 功能描述:IC IMAGE SENSOR STAR1000 84JLCC